![how to make a fast ethernet loopback cable how to make a fast ethernet loopback cable](https://network-byte.com/wp-content/uploads/2020/06/EIA-TIA-568A-standard-min.jpg)
- #How to make a fast ethernet loopback cable android#
- #How to make a fast ethernet loopback cable mac#
You may also need to use a powered USB hub if Android's USB power supply is not enough for connected device. EthernetService is started only if device supports feature USB host ( ) or Ethernet ( ). Your device must be able to operate in USB host mode.
![how to make a fast ethernet loopback cable how to make a fast ethernet loopback cable](https://sc04.alicdn.com/kf/HTB1ZY9Oje3tHKVjSZSgq6x4QFXaz.jpg)
You should be familiar with commandline interface. Note: Everything described below requires a rooted device, or at least the one with unlocked bootloader.
#How to make a fast ethernet loopback cable android#
#How to make a fast ethernet loopback cable mac#
The device does show up as usb0 with the MAC address that was listed in dmesg. Link/ether 42:a1:08:36:5b:0d brd ff:ff:ff:ff:ff:ffģ1: usb0: mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 Link/ether 40:a1:08:36:5b:0d brd ff:ff:ff:ff:ff:ffĢ1: p2p0: mtu 1500 qdisc mq state DOWN mode DORMANT group default qlen 1000 Link/ether c6:b9:c8:82:8f:7e brd ff:ff:ff:ff:ff:ffģ: mtu 1480 qdisc noop state DOWN mode DEFAULT group defaultĢ0: wlan0: mtu 1500 qdisc mq state UP mode DORMANT group default qlen 1000 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0ġ: lo: mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 TX packets:17795 errors:0 dropped:0 overruns:0 carrier:0ĭummy0 Link encap:Ethernet HWaddr c6:b9:c8:82:8f:7e RX packets:27906 errors:0 dropped:4 overruns:0 frame:0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Wlan0 Link encap:Ethernet HWaddr 40:a1:08:36:5b:0d usb 1-1.3: USB disconnect, device number 19 scsi 17:0:0:0: CD-ROM ZTE USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2 scsi 20:0:0:0: CD-ROM ZTE USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2ĭmesg with MTP disabled: usb 1-1.3: new high-speed USB device number 19 using msm_hsusb_host usb-storage 1-1.3:1.2: USB Mass Storage device detected usb 1-1.3: New USB device found, idVendor=19d2, idProduct=1405 usb 1-1.3: new high-speed USB device number 22 using msm_hsusb_host usb 1-1.3: USB disconnect, device number 21 scsi 19:0:0:0: CD-ROM ZTE USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2
![how to make a fast ethernet loopback cable how to make a fast ethernet loopback cable](https://www.edimax.com/edimax/mw/cufiles/images/products/pics/es-1008phe/features/ES-1008PHE_New_Application-Diagram_800x481.png)
usb-storage 1-1.3:1.0: USB Mass Storage device detected usb 1-1.3: Manufacturer: ZTE,Incorporated usb 1-1.3: Product: ZTE Mobile Broadband
![how to make a fast ethernet loopback cable how to make a fast ethernet loopback cable](https://d3fw0f1j2xziep.cloudfront.net/media/catalog/product/c/a/cable_156_om3_mtp_loopback.jpg)
usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-1.3: New USB device found, idVendor=19d2, idProduct=1225 If I disable MTP support, then the device wont register cdc_ether at all.ĭmesg: usb 1-1.3: new high-speed USB device number 21 using msm_hsusb_host The device does not show up as a device in the Android UI / status bar. Is this because it is subsequently mounted as USB storage? The kernel recognizes the device and registers it with cdc_ether, but I am unable to use the connection from the device. I am trying to use an LTE modem connected to an Android 7 device over an OTG cable.